132

Fix That Old Remote With Graphite (hackaday.com)

submitted 1 month ago by mox@lemmy.sdf.org to c/technology@lemmy.world

8 comments fedilink hide all child comments

Surprisingly, the youtube comments contain useful information, too.

top 8 comments

sorted by: hot top controversial new old

[-] mox@lemmy.sdf.org 52 points 1 month ago

This comment from PaulG.x caught my eye:

Electronics technician with 48 years in the industry here.

The common cause of the buttons losing sensitivity is that the silicone absorbs skin oils and these oils act as insulation on the pads and tracks.

If you look at the tracks under the pads that are least sensitive , you will see the oily residue. You can clean the tracks and pads with alcohol for a short term fix but the pads will exude more of the oil that is within the silicone.

A longer term fix is to soak the whole key pad sheet in Fuelite (Petroleum Spirit) Fuelite is the main ingredient in CRC Contact Cleaner (in fact it is the only ingredient). Use liquid Fuelite to do this , not Contact Cleaner because you have to immerse the silicone sheet.

Soak the sheet for 5 minutes , it will swell a little , let it dry thoroughly and it will return to normal dimension.

While the silicone has still some absorbed Fuelite in it , it will be easily torn so treat it carefully.

Then reassemble the device.

This fix should last several months depending on the state of the silicone sheet

[-] vxx@lemmy.world 10 points 1 month ago* (last edited 1 month ago)

This is the way.

I always cleaned the silicone pads with warm water and soap, though. Just put them in the sink, apply water and soap, and use a brush to clean it. Dry it up with a paper towel and slap it a few times on the counter to get the water out of any cracks.

If you don't want to have to clean it at all, don't hold the remote in your hand all day. Condensation will happen.

Also, remotes of smokers are nasty, but soap and water works like a charm here as well.

Use Isopropyl for the electronics. Don't use thinner or anything aggressive. It will just desintegrate the contacts.

As soon as you have to fix the contacts, it's usually better to get a replacement. But if you clean your remote once you have to press harder, the contacts will survive. It's usually from pressing too hard because the contact is bad from dirt.

If you have trouble opening it, twist the remote a bit until it opens or you get enough space between the top and bottom to insert a preying tool.

Watch for eventual screws under labels or in the battery compartment first.

[-] thouartfrugal@lemmy.world 6 points 1 month ago

A longer term fix is to soak the whole key pad sheet in Fuelite (Petroleum Spirit)

Dummy here. Reads to me as a regional brand name and an ambiguous generic term. Would soaking in naphtha work?

[-] mox@lemmy.sdf.org 2 points 1 month ago* (last edited 1 month ago)

A quick search for the mentioned product names found their safety data sheets:

https://www.crcindustries.com/media/msdsen/msds_en-1003333.pdf

Chemical name	Common name and synonyms	CAS number	%
1,1,1,2-tetrafluoroethane	HFC-134A	811-97-2	45 - 55
1,1,2,2-tetrafluoro-1-(2,2,2-trifluoroethoxy) ethane	HFE-347PCF2	406-78-0	45 - 55

https://www.tmkpackers.co.nz/wp-content/uploads/FUELITE-TMK-SDS-ISSUE-6.pdf

Chemical Ingredient	CAS No.	Proportion (% )
Heptane and isomers	mixture	35 - 55
Cyclohexane	110-82-7	25 – 35
Methylcyclohexane	108-87-2	< 15
Hexane	110-54-3	<10

[-] arrakark@10291998.xyz 2 points 1 month ago

Good catch! The POG is always in the comments.

[-] Extrasvhx9he@lemmy.today 6 points 1 month ago

Happens a lot with car rke fobs, I usually have to replace the housings and buttons all together for a permanent fix. I tried the super glue and aluminum foil method and it temporarily works. Nothing I used to attach the aluminum to the worn button pad really results in a long term fix though (super glue, silicone, epoxy, hot glue). Is this a better solution?

[-] vxx@lemmy.world 4 points 1 month ago* (last edited 1 month ago)

The only method that has worked okay for me is using a scalpel to cut off a layer of the silicone from the defective part, and getting a donor pad from another remote to glue it on.

There isn't much room for error though.

[-] db2@lemmy.world 2 points 1 month ago

My go to is a pink pencil eraser. Hit the pad and the contact both then blow away the eraser residue.

this post was submitted on 02 Nov 2024

132 points (98.5% liked)

Technology

60130 readers

2723 users here now

This is a most excellent place for technology news and articles.

Our Rules

Follow the lemmy.world rules.
Only tech related content.
Be excellent to each another!
Mod approved content bots can post up to 10 articles per day.
Threads asking for personal tech support may be deleted.
Politics threads may be removed.
No memes allowed as posts, OK to post as comments.
Only approved bots from the list below, to ask if your bot can be added please contact us.
Check for duplicates before posting, duplicates may be removed

Approved Bots

founded 2 years ago

MODERATORS