Afaik you would destroy the coating on modern lenses, making it worse. That's why I am intensely careful with mine, I only carefully wash them under warm water (not hot) with dish soap without additives, and then use a microfibre cloth to dry. Water and dish soap first to remove anything that could scratch, even microscopic stuff.
After around 4 years of this, mine are almost as good as new still.
Ah unfortunately they've taken a bit of abuse over the years. Nothing major so the scratches are really tiny but enough of them have built up from rough and tumble with the kids etc. that they're a constant annoyance now. :(
I do actually do the dishsoap / warm water thing myself and find it great.
These were my backup pair on a 2 for 1 offer so I didn't get any lens coating / thinner lens thing on them.
I've done it before, using a Dremel tool with a polishing wheel and wax polishing compound, then toothpaste on a rag.
It took me two days, per lens to get anything close to usably clear. So I hate to say it, but you're probably better off getting new lenses.
TL;DR the next part, shit used to be made to last...
Or, if you hit a dumb stroke of luck like I recently did, get some vintage glasses made in the 1980s. It's very rare that I stumble into prescription glasses that match my prescription, but I accidentally came across a perfect matching pair that was manufactured around 1988, and they just refuse to scratch!
Yes, that's almost impossible to stumble across, but you never know what you might find in a thrift store or flea market.
two days, per lens
HOLY MOLY! Fair play to you for the perseverance though.
That’s because they’re glass lenses. The plastic whatever crap is just another form of planned obsolescence.
Nope, can confirm 100%, they're plastic. I just tested the edge with a razor blade, 100% plastic, made before the modern day enshittification and planned obsolescence era.
Damn. I didn’t think they used plastic back in the day, I assumed it was a modern thing. Well. You know what they say about assume. Thx for the correction.
I think my eyesight getting progressively worse every year is a bigger contributor to the glasses industry than planned obsolescence 😭
Are you wearing distance lenses for up close tasks like reading and tapping into Lemmy? There’s evidence that says forcing your eyes to do that through distance lenses speeds up eyesight degradation.
My prescription is -4.75 left, -4.5 right, and about 15⁰ astigmatism.
Now I'm wearing bifocals made before my first prescription, and these glasses just work.
Myopia. Nearsightedness. Can't see a pile of horse shit in front of your feet sorta blind.
Glasses are awesome though, ugly or not..
...well that's just great, I wish someone had told me this before my eyesight was at -6.00
Could a local optician sort it?
You know, this is so blindingly obvious I never thought of it. Haha! Great idea.
edit: I actually can't believe I didn't think of this. Chuckling away to myself here.
edit 2: I looked up the opticians I bought from and they have a page about scratches that says they can't unfortunately. :( It recommends new lenses. Not sure if that's profit motive or not though.
Polishing is how the lenses are shaped into your prescription; buffing out scratches would change the shape of the lens
my undaeratanding is that lens material is so optically tuned for weight that removal of any amount of material makes a difference to the focusing - not to mention the possible coatings on the lens. this is what I have been told, I have no other evidence.
blindingly obvious
Perfect.
Costco's optometrist said they couldn't buff out the scratches on mine since they don't actually use glass anymore. They use polycarbonate lenses which are strong and won't shatter if broken (I've definitely tested this on accident...)
Code at checkout: BOGO
Last time I bought glasses there, it cost me ~60$ for 2 pairs. Both with scratch resistant coatings, and one with a photochromic coating (auto tint in sunlight).
Just wanted to come back and say thanks. I emailed my optician for my prescription and bought a pair of glasses off this site for €17 delivered (about $19 USD). Do you mind me asking how long yours took to arrive? I'm in one of the "standard delivery" countries.
If I remember right, it was just over 2 weeks; but it's been a couple years since I ordered.
I've ordered my last 2 sets from there, and had at least 3 family members ordering from there too. We've never had any issues aside from one poorly fitting set, which they returned and got fresh ones free of charge. I really couldn't be happier with goggles4u.
I've really got to get around to seeing the optometrist and getting a fresh prescription... Time flies.
You will not believe this but when I emailed for my prescription earlier I was told I'm well overdue (2021 was my last test) and I said "time flies". She took the time to write "OUT OF DATE" twice on the scan.
Thanks for the timeline.
Thanks. Just had a look and that is incredibly cheap. They also do ~~free~~ standard shipping to my country so I will seriously consider this.
Zenni optical is another affordable online option! Or eye buy direct. I've only used Zenni, but all of my glasses since like 2011 have come from them and I've had 0 issues!
Ah! I knew there was a place someone had mentioned to me before that they were happy with and couldn't remember the name. It was Zenni. I ended up buying from that site linked above for very cheap and I'm going to do some experimenting with these scratched ones when the new ones get here.
Buffing your lens with a tool will damage the coating and worst, it can change the shape and distort your view.
Even if you use a softer method, it will still affect the coating and your glasses will get dirtier faster and be harder to clean
The best solution is to not mess with it and simply get new glasses if it becomes too unbearable.
Stuff like toothpaste is way too coarse for things like this. It isn't something I have tried as I don't wear glasses but have you considered trying something like a rubbing compound used during paintwork on cars etc?
It is basically a fine grade liquid sandpaper and is used to buff up the final laquer coat to a good shine.
Pretty sure you can get different grit levels and may require some elbow grease but may be an option worth looking at?
You pay more initially, and have to look around more for it, but glass lenses hold up. Drop them. Stick them in your pocket with your car keys and pens. Clean them with whatever. Lose the case on day one. And they stay scratch free. For years.
Granted, this is only tenable if you have a “lighter” prescription.
I remove mine for close up stuff and thus my prescription has remained the same for over 20 years. I get new glasses not because the lenses scratch up, but because the frames break. I average new glasses every 8-10yrs.
Glass lenses.
I've never even been offered glass lenses. I thought they were phased out so that people would never get broken glass in their eyes.
I’m been smacked in the face and dropped them multiple times on concrete, industrial linoleum tile, and hardwoods. Never even seen a crack. I’m sure there are things that can do so, like an airbag exploding in your face, but I can’t imagine shattered broken milled plastic not being dangerous as well.
You have to ask for glass. They bury it in favor of the garbage that scratches up over time.
Quality plastic lenses can last that long. Often being able to keep glasses that long depends most on the stability of your prescription, and not going for bottom of the barrel coatings.
Glass lenses are harder to scratch, but are heavier for the same prescription and if you get hit in the face can shatter into shards that are quite damaging to the eyes.
If getting hit in the face is not a risk for you and you dont mind the extra weight go for it, but it's worth noting there are some downsides as well.
That’s why I said it depends on how light your prescription is. The husband has coke bottle lenses and cannot do glass. But he has to use the case. He has to use a special cloth to clean the lenses. He has to check against cleaning chemicals. He has to be very careful or they scratch, doesn’t matter what “special coating” is there. Those lenses do scratch up.
I’m less than -2 in both eyes so the weight doesn’t matter so much for me. I drop mine on the (bacterial lava) floor of a patient care area and I can grab whatever industrial, don’t use bare hands, wipe is available to purge the lenses of bacterial and viral load. And then stick them loose in a pocket with keys, pens, loose change, scissors, and they come out after a couple hours of that scratch free.
I get hit in the face. For decades. And decades of dropping them on concrete and everywhere else. No issues, breaks, or scratches thus far.
What are the stats on that? Are they a reality for the curved milled glass lens? Or is it a falsehood used to sell planned obsolescence lenses?
Lol. Bullshit to quality plastic lenses last that long. I mean sure, if you never drop them and baby the heck out of them.
The hardest clear plastic isn't remotely close to being as hard as glass or sapphire.
As for the shatter thing, often glass lenses will have a plastic layer on the eyes side of the lenses that prevents shards. This does mean that the inside of your glasses will scratch easier than the outside, but the outside is what always gets abuse.
Not all plastics are made equal. Two different 1.5 or 1.6 index plastics from different manufacturers will have different scratch resistance as well as different levels of aberration depending on how good their materials science is.
All plastic is softer than glass, yes, which is why any plastic lens you get has a hardcoat to reduce scratching and if it is from a quality lab, a scratch/antireflective coat as well.
If you've never had plastic lenses last very long, where you are sourcing them from is using inferior quality plastics with whichever lab partner they use. That or you a) leave them in a hot car and the heat damages them b) constantly leave them lens-face down on the table
But I have had people with very stable prescriptions keep plastic lenses in good condition for 15-20 years in extreme cases.
Laminated glass treatments may be used, but because they cause problems with the cutting machinery it is far more common in optical glass lenses to see chemical or heat treating. If these are done well, they can be quite resistant to shattering. This, however, really comes down to the individual skill of the person treating your lens and I've seen enough damaged eyes to be wary of them.
Another reason many labs have moved away from mineral lenses entirely is that they shatter when being cut to shape for your glasses, posing greater risk to the one doing the edging and significantly greater cost to the lab. Depending on the complexity of prescription they may shatter up to 3 or 4 times before one cuts properly into shape.
To add onto this, if you are using progressive glasses, you are certainly getting an inferior product as no lab I'm familiar with puts their new progressive designs into mineral. The majority only have designs from 15-20 years ago with terrible intermediate segments.
I recently viewed and saved a post regarding modern day lens coatings. Took me a bit to find it..
https://lemmy.world/post/18532120
There's also a particular comment in that thread that says what chemical they use to remove that coating. Check back soon and I'll reply to this comment with a link to that particular comment...
Addendum, found the comment of interest..
I don't think it would work in the slightest either way but rather than buff them out, maybe find something to fill in the scratches.
Yeah one of the recommended things I saw was furniture polish or car wax to fill them in. Both would only be temporary. Based on the replies so far I may give this a whirl as I don't see it being damaging.
I don’t know about outer coatings, but I always wondered if lapping film would work on glass lenses. Think super fine sandpaper for fiber optic cables.
I tried it once. It didn’t go well
You'd need to be able to replace the coatings on them. The scratch would likely be the easier part. The coatings might be hard to get. Most sold commercially are not as permanent and industrial ones are either very proprietary or require expensive equipment that wouldn't be worth it for a one pair of lenses.
After you get your replacement lens, you can also try putting a drop of resin and wiping it away. In theory the resin should fill the crack with a transparent material and the heal the blemish. Then you "buff it" by removing excess liquid before it cures. But as others mentioned there is coating and more specifically glass treatment that may cause issues, but that's the process for auto class repair (they usually drill out a hole around it first to prevent further spreading but that sounds worse here). Those kits can be pretty cheap
Don't have a solution, want to leave this here for the advice
1) Be nice and; have fun
Doxxing, trolling, sealioning, racism, and toxicity are not welcomed in AskLemmy. Remember what your mother said: if you can't say something nice, don't say anything at all. In addition, the site-wide Lemmy.world terms of service also apply here. Please familiarize yourself with them
2) All posts must end with a '?'
This is sort of like Jeopardy. Please phrase all post titles in the form of a proper question ending with ?
3) No spam
Please do not flood the community with nonsense. Actual suspected spammers will be banned on site. No astroturfing.
4) NSFW is okay, within reason
Just remember to tag posts with either a content warning or a [NSFW] tag. Overtly sexual posts are not allowed, please direct them to either !asklemmyafterdark@lemmy.world or !asklemmynsfw@lemmynsfw.com.
NSFW comments should be restricted to posts tagged [NSFW].
5) This is not a support community.
It is not a place for 'how do I?', type questions.
If you have any questions regarding the site itself or would like to report a community, please direct them to Lemmy.world Support or email info@lemmy.world. For other questions check our partnered communities list, or use the search function.
6) No US Politics.
Please don't post about current US Politics. If you need to do this, try !politicaldiscussion@lemmy.world or !askusa@discuss.online
Reminder: The terms of service apply here too.
Logo design credit goes to: tubbadu
