In 2023, my goal was 4,000 miles, and I made it, so I started with the same this year.

In late September, 2024, my local club did a ride across our state, about 350 miles over 4 days. After that, I was about 20 miles shy of the 4,000 goal, and hit it within the following week. I normally ride 80-120 miles per week, so 350 was a huge jump.

Then, I upped the goal to 5,000 miles, then finished that in late November or early December. A friend congratulated me and noted that 5,000 miles was almost 100 miles per week, so I made the new goal 5,200 miles.

Of those 5,348 miles, 2,111 miles (~39%) were on Zwift. I did three imperial centuries on Zwift this year, and several more metric centuries on Zwift. The rest were all outdoor, ranging from 25 miles to 120 miles.

I haven't decided on a goal for next year yet. Right now it's at 5,200 miles (it automatically resets to the same). But, for various reasons, I'm not sure whether I'll ride that much this year.

First, the good news: My friend is essentially okay, aside from some bumps and bruises. His bike took some damage, but likely not catastrophic: From what we could tell, both derailleurs on his bike and the bar tape were damaged; there may be other damage we couldn't identify immediately, such as the handlebars themselves.

We were riding on this road with two lanes, no shoulder, and there's a light at the bottom of a hill, with a right turn lane. The light was green, so our group was cruising at a pretty high pace - probably 25 or 30 mph - in the right lane (not the turn lane, the through lane) and some driver needed to turn right, but couldn't wait a few seconds. So, they went into the LEFT lane, then turned right in front of our group, hit one of our riders, and kept going.

("Must get in front...oh I have to turn here..." Shitty driving habits in general, I'll bet.)

A few other cars stopped, and someone called the police, who took a report and got an ambulance to check out the victim. Hopefully they'll do some investigation and find the guilty party. The cross street leads into a neighborhood with no other exits, so there's a good chance the perpetrator lives there. Also there is a camera at that light, and one person thought to note the exact time it happened, in case the camera does continuously record.

I hope they find the driver. They deserve to pay for all damages and a huge fine.

Our friend commented that his bike was likely worth more than the minivan that hit him, which is almost certainly true, given it was an older model van and his bike is a high end Pinarello. He also noted that none of us stopped his bike computer, which was good for a laugh.

The ride leader's husband was able to come and pick up her, the victim, and another rider that wasn't comfortable continuing after the crash (we were only about halfway through the planned route). The rest of us pedaled on, albeit a bit more subdued for a while.

Hi, all. Finally migrated from Kubuntu to Debian 12 over the weekend. It's working great, as I figured it would, with one exception: The system isn't turning the monitors off after 10 minutes. It's blanking them, but they're clearly still on.

One monitor is on an AMD graphics card, the other is on the motherboard Intel adapter.

Debian 12 with KDE Plasma running on Wayland with sddm login. It previously worked fine on Kubuntu (which I believe was running X11). It's a fresh Debian install on a different drive; I didn't overwrite the Kubuntu installation.

In the Energy Saving settings, I have "Screen energy saving" checked with a delay of 10 minutes. (I have "suspend session" turned off - one, because I don't want the computer to sleep or suspend, and two, because when I woke it up again, the graphics were garbled and I had to reboot.) As I said, it does blank the screens, but they're still clearly on. I want them to go into power save mode.

I've tried running dpkg-reconfigure and selecting sddm, no change. In KDE's background services, I tried turning off KScreen 2, but that didn't help (though I'm not sure if I rebooted after turning it off, now that I think about it).

I found advice somewhere that suggested deleting .config/powermanagementprofilesrc and rebooting; I did that, no change.

I did notice yesterday that the monitors had shut off...after a very long time of being idle. I'm not sure how long, but more than overnight, for certain.

Any advice or suggestions? Unfortunately, searching is difficult, because I get a lot of results where the screen blanks when it shouldn't. I haven't found much for this problem.

I used the same installer on my laptop to do the same migration (also with KDE Plasma and sddm) and it works fine there.

Hello! I don't have pictures yet, but I finally finished my mixed road/gravel bike and took it for a short ride (in wet conditions) over the weekend, and I wanted to celebrate a bit. Sorry for the long post!

I bought the frame on sale a few months back from Velo Orange, it's their Pass Hunter model. I had been kind of eyeing them up for years, as they're based near me, for this kind of bike. My eventual goal is to tour the GAP and C&O canal trails with it - my road bike, a CAAD12, would not be up to such a tour. I'll also take it with us when we go camping - we were out west for a few weeks last year, and there were a lot more gravel roads than this east coaster is used to.

The groupset is a GRX Di2 2x11 with hydraulic discs. I know some will disagree with the electronic shifting for a touring rig, but I've read all of the arguments on both sides, and it's what I wanted. In hindsight, I wish I'd realized that the VO Pass Hunter frame isn't really Di2 compatible, because there are limited options for fishing the wires through the frame - a restriction that never even occurred to me until after I had everything. But I can live with it.

This is my first build, my first experience (ever) with electronic shifting, and my first experience with disc brakes (aside from a very short test ride years ago), and my first experience with hydraulic brakes. Lots of learning!

The wheels are from Bikesdirect.com - did you know they have decent deals on wheels, too? DT Swiss rims, Shimano hubs, Shimano rotors, 38c tires mounted, rim and tires tubeless ready, but set up with tubes. I got 700s, but I probably should have gone with 650b for the clearance on the rear wheel. Longer term, I'll pick up a set of 650bs with mixed road/gravel tires, and put pure road tires on my 700c wheels.

I had a bike fit on my road bike (a CAAD12) done a few years ago, so I used the results from that as a guideline for this build. In particular, the top tube on the VO is longer than the Cannondale, so I got a shorter stem to compensate.

I did end up getting wider handlebars (46 instead of 44), but the gravel handlebars feel a LOT wider than the road handlebars. Which, for an all day ride, probably isn't a bad thing - more positions.

I want to test it more, but I'm thinking I'll set the handlebars a little higher than my CAAD12's are, relative to the seat height - because, one, they're wider, so my arms are out farther when I'm on the hoods, meaning I'd be leaning down a bit farther, and two, comfy, all-day touring bicycle.

The bike is all black. I'm not very imaginative. It's like, how much more black could it be? None. None more back. I don't usually name my bicycles, but suddenly I want to call this one "Smell the Glove". (The VO paint is actually black with flakes and a chrome logo, it looks pretty cool.)

It's definitely a slow bike with the weight and tires on it now, but that's okay - the point was to build a comfortable, ride-all-day tourer, not a speed demon. It weighs 24 lbs without water bottle cages, bike bags, etc.

After my test ride, I'm even happier with my decision to go Di2. And that's with repeatedly hitting the wrong buttons to shift on the ride (I have no idea why I was doing that, it's essentially the same as the 105 5800 on my CAAD12, but I kept doing it).

Bar tape: I am terrible at wrapping bars. I have no fear of the mechanical or electronic portions of building a bike, but bar tape...I dunno. It's very stressful for me, I think because it's so visible, and I feel like everyone is looking at it and going, LOOK WHAT THAT AMATEUR DID! But, I think I actually did a credible job on this one, for once. Tip for anyone else that suffers the same phobia: Look for extra long tape, it's one less stressor!

Suppliers: Frame came from VO, obviously. I got the Di2 setup off eBay - oddly enough, that seems to be the easiest way to buy a groupset, if you need the whole thing. Bikesdirect.com for the wheels. I went to Biketiresdirect.com for a lot of the parts, and when I couldn't find what I wanted or needed there, I went to Amazon. I ordered a few random parts from other places, too - I think the handlebars came from another bike parts supplier.

Costs: I expected this to cost more than a pre-built bike would, but if I wanted that VO frame, building one was my only option. But now that I think about it, I might have actually saved a little money this way. This bike, the first result on google for "Di2 gravel bike", is $3495 with 2x, and I'm pretty sure I have less than that into my build. And I included pedals and a good saddle that fits me in the cost, neither of which comes with most pre-built bikes.

Plus, I probably put a few better components on than would be stock, like softer bar tape, and Easton stem and seat posts, and so on. And, I got the parts I needed - such as the correct stem length for me - so I'm not replacing parts that came with a pre-built bike, either.

So, while it doesn't feel like it, I probably did actually save some money over a pre-built bike. Of course, I spent hours working on it, and I bought several new tools at the same time - strangely, I never had a bike stand before, so I bought one as part of this build. (I don't count the tools as part of the build costs, as I'll very likely use them again.)

To do yet:

• Ride it and adjust the handlebar height as desired, then eventually cut the steerer tube, again. I did an initial cut to get it in the right ballpark, but there's likely another inch or so that could come off.

• Check the rear brake - it engages a lot lower than the front brake, so it might need to be bled. I adjusted the engagement point, but it's still quite different compared to the front. It doesn't feel spongy, and I can lock up the wheel, it just travels a lot farther back. I'd rather it be more consistent with the front brake.

• Adjust the clipless pedal tension. I'm used to SPD-SL cleats, and I've used SPD before, but I was having a miserable time with these at first, so I loosened the tension. I'll want to crank that back up.

• RIDE IT!

Mistakes I made:

• My biggest was the Di2 wiring thing. The frame was really intended to have cables, so I have bosses for shifters or cable mounts that I'm not using (they're covered with caps that are the same color as the frame, at least). I wonder how hard it is to remove that thing - I had to repair similar downtube bosses on my old aluminum bike, and that just had a metric threaded rod running between the two sides. Maybe cut a rubber plug for the holes...hmmmmmmmmm.

• I bought a second band clamp because I thought the first one was interfering with one of the water bottle cage bolts...but while I was waiting for the new clamp to arrive, I figured it out with the original clamp. Not sure what I was going wrong at first.

• There are a few spots I could switch to shorter Di2 cables, but the necessary length is extremely hard to predict, I've learned, and those cables are not cheap. One that's too long is the one for the rear derailleur, and that one would be very easy to change and could be done whenever I feel like it. The other is the cable from the junction near the bottom bracket to the shifter - I have a 1200 mm cable, but a few cm shorter wouldn't have hurt. But neither one is so long that it's a major problem, either.